Wild Dog Adventure Riding

Technical Section => Make / Model Specific Discussions => Suzuki DR & DRZ => Topic started by: LouisXander on January 21, 2013, 01:38:07 pm

Title: DR200. Rolling chassis/spares up for grabs.
Post by: LouisXander on January 21, 2013, 01:38:07 pm
Can anyone help? I'm looking for a DR200 oilcooler.

Thx
Title: Re: DR200 Oil cooler
Post by: DeepBass9 on January 21, 2013, 02:31:20 pm
Can anyone help? I'm looking for a DR200 oilcooler.

Thx

My farm worker farked up the engine on his DR 200 (don't ask I've never seen a piston with a hole through it before). But he used to have a complete bike. I can enquire if he still has it if you want. Just clean out that oil cooler very well if you use it, there will be lost of metal inside.
Title: Re: DR200 Oil cooler
Post by: LouisXander on January 21, 2013, 02:37:07 pm
Much appreciated DB!
Title: Re: DR200 Oil cooler
Post by: lecap on January 22, 2013, 08:09:36 am
You don't really need it. The DR200 is not an SACS engine and only the agri DR versions actually have the oil cooler. The "proper" DS DR200SE and Djebel 200 came and did well without it.
Title: Re: DR200 Oil cooler
Post by: gser on January 22, 2013, 10:33:50 am

 The agri DR200 is the DF200
Title: Re: DR200 Oil cooler
Post by: ®©errie on January 22, 2013, 04:27:41 pm
Can anyone help? I'm looking for a DR200 oilcooler.

Thx

My farm worker farked up the engine on his DR 200 (don't ask I've never seen a piston with a hole through it before). But he used to have a complete bike. I can enquire if he still has it if you want. Just clean out that oil cooler very well if you use it, there will be lost of metal inside.

PM Send
Title: Re: DR200 Oil cooler
Post by: DeepBass9 on January 23, 2013, 08:59:16 am
I have spoken to Rapula and he has the complete bike and all its parts. The engine is farked but the gearbox and casings should be OK. He wants R2000 for it. Maybe you guys should buy it and strip and sell off the parts as required?
Title: Re: DR200 Oil cooler
Post by: ®©errie on January 23, 2013, 09:11:35 am
Thanks, whoever buys the complete bike I would like to buy the starter idler gear
 :biggrin:
Title: Re: DR200 Oil cooler
Post by: chopperpilot on January 23, 2013, 02:18:07 pm
Goose was looking for a kick starter and kick starter shaft. PM him to share some costs. :thumleft:
Title: Re: DR200 Oil cooler
Post by: ®©errie on January 23, 2013, 02:30:59 pm
LouisXander - Oil Cooler
Goose - Kick Starter/Shaft
RCerrie - Starter Clutch Idler gear + pin and spacer
Title: Re: DR200 Oil cooler
Post by: DeepBass9 on January 23, 2013, 02:40:25 pm
LouisXander - Oil Cooler
Goose - Kick Starter/Shaft
RCerrie - Starter Clutch Idler gear + pin and spacer

Put the price that you are prepared to pay for each part.
Title: Re: DR200 Oil cooler
Post by: ®©errie on January 23, 2013, 02:45:28 pm
LouisXander - Oil Cooler
Goose - Kick Starter/Shaft
RCerrie - Starter Clutch Idler gear + pin and spacer  R200 + R60 speedservices
Title: Re: DR200 Oil cooler
Post by: Goose on January 23, 2013, 03:54:24 pm
LouisXander - Oil Cooler
Goose - Kick Starter/Shaft
RCerrie - Starter Clutch Idler gear + pin and spacer  R200 + R60 speedservices



YES PLEASE... HUGE BIG PRETTY PLEASE!!!!!!   :thumleft:   Ek sal betaal... just say where and to whom!!!   :thumleft:
Title: Re: DR200 Oil cooler
Post by: ®©errie on January 23, 2013, 03:57:36 pm
Parts Base to LouisXander.....Parts Base to LouisXander.......come in please...
Title: Re: DR200 Oil cooler
Post by: DeepBass9 on January 23, 2013, 04:01:07 pm
I think we need LX here, I have no idea what these parts look like!
Title: Re: DR200 Oil cooler
Post by: LouisXander on January 23, 2013, 04:03:36 pm
What do you offer on an oil cooler? R250? Still short on R2k. Goose must buy the rest of the scoot I think!
Title: Re: DR200 Oil cooler
Post by: Goose on January 23, 2013, 04:10:46 pm
LouisXander - Oil Cooler
Goose - Kick Starter/Shaft
RCerrie - Starter Clutch Idler gear + pin and spacer  R200 + R60 speedservices



YES PLEASE... HUGE BIG PRETTY PLEASE!!!!!!   :thumleft:   Ek sal betaal... just say where and to whom!!!   :thumleft:

I can pay R300 + R60 postage for the 2 parts........
Title: Re: DR200 Oil cooler
Post by: ®©errie on January 23, 2013, 04:16:37 pm
I think we need LX here, I have no idea what these parts look like!

Idler gear + pin (spacer not in photo)

(http://i669.photobucket.com/albums/vv57/rcerrie/gear_zps90a628ba.jpg)
Title: Re: DR200 Oil cooler
Post by: ®©errie on January 23, 2013, 04:21:34 pm
LouisXander - Oil Cooler
Goose - Kick Starter/Shaft R300 + R60 postage for the 2 parts
RCerrie - Starter Clutch Idler gear + pin and spacer  R200 + R60 speedservices

Title: Re: DR200 Oil cooler
Post by: LouisXander on January 23, 2013, 04:50:00 pm

LouisXander - Oil Cooler/piping R300+collect myself
Goose - Kick Starter/Shaft R300 + R60 postage for the 2 parts
RCerrie - Starter Clutch Idler gear + pin and spacer  R200 + R60 speedservices

Title: Re: DR200 Oil cooler
Post by: DeepBass9 on January 23, 2013, 06:37:33 pm
OK, no one keen for the whole bike?

I'll see if I can get hold of the bits over the weekend, I'll let you know when I have them.
Title: Re: DR200 Oil cooler
Post by: ®©errie on January 23, 2013, 08:47:24 pm
OK, no one keen for the whole bike?

I'll see if I can get hold of the bits over the weekend, I'll let you know when I have them.


Thanks
Title: Re: DR200 Oil cooler
Post by: Goose on January 24, 2013, 02:42:24 pm
OK, no one keen for the whole bike?

I'll see if I can get hold of the bits over the weekend, I'll let you know when I have them.


Thanks


That would be great............     :thumleft: :thumleft:
Title: Re: DR200 Oil cooler
Post by: DeepBass9 on January 24, 2013, 02:52:34 pm
LX, can you change the name of the first post to see if anyone else wants some bits...
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: LouisXander on January 24, 2013, 03:52:37 pm
LX, can you change the name of the first post to see if anyone else wants some bits...

Done!
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: Beltzer on January 24, 2013, 09:14:37 pm
carb available? i might know someone who would be interested
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: kelly007 on January 24, 2013, 09:50:31 pm
front disk please (if useable) 200


Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: Ratt on January 24, 2013, 10:00:41 pm
Jy reg gekom met die cdi RC? Hoe lyk die fiets? Mag dalk belang stel in die rollling chassies
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on January 25, 2013, 07:29:27 am
I'm going to fetch it early next week. The bike is intact, but the engine is in a box with the top end off. I'll post some pics when I have it. Yes there is a carb, yes there is a CDI and a front disc.

Watch this space next week.
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: Goose on January 25, 2013, 07:47:16 am
If the Carburettor is intact with the "Idler lever, spring and bolt"  intact - I'll take that as well...........  R 200.00 offered and will combine wif postage.....




LouisXander - Oil Cooler
Goose - Kick Starter/Shaft R300 + R60 postage for the 2 parts + Carburettor - R 200
RCerrie - Starter Clutch Idler gear + pin and spacer  R200 + R60 speedservices
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: ®©errie on January 25, 2013, 07:52:41 am
DB, please include pics of the 2 handlebar switch units (Flicker and starter/kill unit) thanks
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on January 25, 2013, 08:32:23 am
OK, will do.
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: LouisXander on January 25, 2013, 08:49:45 am
Complete the list guys!! So we can get an idea of the costs.
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: ®©errie on January 25, 2013, 08:53:47 am
LouisXander - Oil Cooler/piping R300+collect myself
Goose - Kick Starter/Shaft R300 + R60 postage for the 2 parts
RCerrie - Starter Clutch Idler gear + pin and spacer  R200 + R60 speedservices
            - 2x Handlebar switches R200
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: Goose on January 25, 2013, 09:42:20 am
LouisXander - Oil Cooler/piping R300+collect myself
Goose - Kick Starter/Shaft R300 + R60 postage for the 2 parts[/b]
RCerrie - Starter Clutch Idler gear + pin and spacer  R200 + R60 speedservices
            - 2x Handlebar switches R200




 :eek7:  erm.....  

Goose - Kick Starter/Shaft R300 + R60 postage for the 2 parts + Carburettor - R 200  .............Total R 500 + R60 postage
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: ®©errie on January 25, 2013, 10:04:57 am
- R200......hoe werk dit????  :imaposer:
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: ®©errie on January 25, 2013, 10:06:38 am
OK OK, new list

LouisXander - Oil Cooler/piping R300+collect myself
Goose - Kick Starter/Shaft R300 + R60 postage for the 2 parts + Carburettor - R 200  .............Total R 500 + R60 postage
RCerrie - Starter Clutch Idler gear + pin and spacer  R200 + R60 speedservices
            - 2x Handlebar switches R200
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: LouisXander on January 25, 2013, 10:46:38 am
Kom Beltzer, waar is jy?
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: ®©errie on January 25, 2013, 10:57:41 am
Kom Beltzer, waar is jy?

Louis, vat die res vannie fiets  :peepwall:

Ek en Goose is te ver
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: Sláinte Mhaith on January 25, 2013, 10:58:41 am
Stator Coil?
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: LouisXander on January 25, 2013, 10:59:02 am
Nope, het niks verder nodig nie.
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on January 25, 2013, 10:59:51 am
Stator Coil?

Yup. Should be there.
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: ®©errie on January 25, 2013, 11:23:04 am
If the airfilter is still ok, I would like to take it, little pipe at bottom of airbox and 2x Tappet inspection covers

Thats it for me!!!!
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: ®©errie on January 25, 2013, 11:27:01 am
LouisXander - Oil Cooler/piping R300+collect myself
Goose - Kick Starter/Shaft R300 + R60 postage for the 2 parts + Carburettor - R 200  .............Total R 500 + R60 postage
RCerrie - Starter Clutch Idler gear + pin and spacer  R200
            - 2x Handlebar switches R200
            - 2x Tappet Inspection caps, Airfilter and breather tube  R40.............Total  R440 + 60 speedservices
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: Goose on January 25, 2013, 04:38:36 pm
Jong - maybe we should take the rest............  any chance of a WD coming to Cape Town........?  Transport is the biatch.......  hell I collected a whole XT550 in the boot of the Charade......... surely we could have the rest stripped down and sent to the Cape...?   :peepwall: 

I'd love the swingarm as well.........  my son's one is damaged after that accident.......... however the transport/postage is what's gonna eat us......... unless we can get a quote from Time Freight?
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: kelly007 on January 25, 2013, 09:31:28 pm
LouisXander - Oil Cooler/piping R300+collect myself
Goose - Kick Starter/Shaft R300 + R60 postage for the 2 parts + Carburettor - R 200  .............Total R 500 + R60 postage
RCerrie - Starter Clutch Idler gear + pin and spacer  R200
            - 2x Handlebar switches R200
            - 2x Tappet Inspection caps, Airfilter and breather tube  R40.............Total  R440 + 60 speedservices
Kelly007 - front disc 200 plus postage
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: Beltzer on January 26, 2013, 02:29:50 pm
Kom Beltzer, waar is jy?

wat moet ek doen? ek soek die carb, maak n prys asb..




Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: Sláinte Mhaith on January 27, 2013, 01:58:49 pm
LouisXander - Oil Cooler/piping R300+collect myself
Goose - Kick Starter/Shaft R300 + R60 postage for the 2 parts + Carburettor - R 200  .............Total R 500 + R60 postage
RCerrie - Starter Clutch Idler gear + pin and spacer  R200
            - 2x Handlebar switches R200
            - 2x Tappet Inspection caps, Airfilter and breather tube  R40.............Total  R440 + 60 speedservices
Sláinte - Stator coil and voltage regulator  - R400?
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: Goose on January 29, 2013, 11:33:01 am
 :peepwall:
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: ®©errie on January 30, 2013, 07:41:36 am
 :peepwall: :peepwall:
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on January 30, 2013, 08:10:04 am
I'm going to fetch the bike on Saturday, I'll probably strip the parts off on Sunday. Patience........... :pot:
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: Goose on January 30, 2013, 09:23:08 am
I'm going to fetch the bike on Saturday, I'll probably strip the parts off on Sunday. Patience........... :pot:


 :thumleft:
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: chopperpilot on January 30, 2013, 10:37:11 pm
I might be interested in the rest. :thumleft:

First need to follow up on a possible donor bike. ???

Price for the rest DB9? (PM pse.) (Let me first find out on the donor bike!) ??? :thumleft:
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on January 31, 2013, 07:19:06 am
Make me an offer. I don't want my place to look like a bike scrapyard, so please take the remains.
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: chopperpilot on February 01, 2013, 05:01:29 pm
Make me an offer. I don't want my place to look like a bike scrapyard, so please take the remains.

Sorry DB9. The possible donor bike has been sold.  :(

Saw it a while ago on Gumtree. Googled the ad again. (Had front end damage.) Would have been perfect!
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: madmike999 on February 01, 2013, 05:23:45 pm
just a question, is there a rear rim available?
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on February 01, 2013, 05:55:58 pm
just a question, is there a rear rim available?

Yup, is an 18" as far as I am aware.
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: madmike999 on February 01, 2013, 06:13:26 pm
how much....
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on February 01, 2013, 06:16:59 pm
how much....


Whatever it is worth to you.
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on February 06, 2013, 05:53:40 pm
Ok, I've got the bike. I'll get it cleaned tomorrow and then strip off the parts.
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: ®©errie on February 06, 2013, 05:57:05 pm
Cool, please remeber to take some pics of parts
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: Goose on February 06, 2013, 07:46:24 pm
Ok, I've got the bike. I'll get it cleaned tomorrow and then strip off the parts.


Fantastic mate!  :thumleft:

When pics of the bike is posted..... I'd be interested in the tank, seat and swing arm as well....
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on February 07, 2013, 08:17:26 am
Ok, I've got the bike. I'll get it cleaned tomorrow and then strip off the parts.


Fantastic mate!  :thumleft:

When pics of the bike is posted..... I'd be interested in the tank, seat and swing arm as well....

The tank has a dent, and the swingarm had been welded. Seat OK.
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on February 10, 2013, 10:43:36 am
Taking the parts off today. There is a steel braided front brake hose. Anyone interested?
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on February 10, 2013, 12:13:28 pm
So this is what I have:

LouisXander - Oil Cooler/piping R300+collect myself  - tick (remember to get that high lift jack bracket as well)


Goose - Kick Starter/Shaft R300 + R60 postage for the 2 parts + Carburettor - R 200  .............Total R 500 + R60 postage

Carb I have, Do you need to split the engine to get the kick started shaft out?


RCerrie - Starter Clutch Idler gear + pin and spacer  R200  - Presumably also in the guts of the engine?

            - 2x Handlebar switches R200 - Tick

            - 2x Tappet Inspection caps, Airfilter and breather tube  - tick.  R40.............Total  R440 + 60 speedservices

Sláinte - Stator coil and voltage regulator  - R400?  -Where does the voltage regulator sit?



There is also the CDI if anyone wants it.
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: Goose on February 10, 2013, 12:17:23 pm
So this is what I have:

LouisXander - Oil Cooler/piping R300+collect myself  - tick (remember to get that high lift jack bracket as well)


Goose - Kick Starter/Shaft R300 + R60 postage for the 2 parts + Carburettor - R 200  .............Total R 500 + R60 postage

Carb I have, Do you need to split the engine to get the kick started shaft out?


RCerrie - Starter Clutch Idler gear + pin and spacer  R200  - Presumably also in the guts of the engine?

            - 2x Handlebar switches R200 - Tick

            - 2x Tappet Inspection caps, Airfilter and breather tube  - tick.  R40.............Total  R440 + 60 speedservices

Sláinte - Stator coil and voltage regulator  - R400?  -Where does the voltage regulator sit?



There is also the CDI if anyone wants it.


I'll give R50 for the CDi............

I don't know the DT engine at all.... but if anything like the XT motor. then the side cover comes off and the shaft should easily just pull out?

 :peepwall:  will go and check....  can I send you info via email.

Oh............... DB9  for all your effort and trouble matey........... what do we lot owe you?  Surely you cannot be expected to do all this work for nothing..... maybe a beer fund/collection?   :thumleft:
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on February 10, 2013, 12:29:10 pm
You are aware this is a DR?  ??? Anyway, I've pulled on the shaft but it doesn't seem to want to come out, I think there must be somthing holding it in place from inside the crank case. Does anyone have a workshop manual? steve(at)dreamlodge.co.za
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: ®©errie on February 10, 2013, 12:46:05 pm
Gear pin and spacer located behind the stator cover (lower left bottom side of engine)
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: ®©errie on February 10, 2013, 12:57:59 pm
Gear pin and spacer located behind the stator cover (lower left bottom side of engine)

Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: ®©errie on February 10, 2013, 02:53:22 pm
Had to change my wiring harness, since the master fuse kept blowing on the old loom. Looks like I blown the recently accuired cdi from ebay. 

I can offer R150 on CDI....
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: Sláinte Mhaith on February 10, 2013, 05:26:27 pm
  -Where does the voltage regulator sit?

It should be on the frame under the tank or seat somewhere.

Looks like this

(http://i.ebayimg.com/t/Suzuki-DR-200-DR200SE-DR200-Voltage-Regulator-Rectifier-08D10-SH553B-13-/00/s/MTIwMFgxNjAw/$(KGrHqV,!qEFBfVFNTB!BQhJ,LbGNg~~60_35.JPG)
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: Sláinte Mhaith on February 10, 2013, 05:29:19 pm
Taking the parts off today. There is a steel braided front brake hose. Anyone interested?

Might take it if no one else is in serious need of one.
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: lecap on February 11, 2013, 11:11:13 am
Kindly note my thread re. the swingarm pivot needle bearing upgrade http://www.wilddog.za.net/forum/index.php?topic=117523.0
I have only one set left. The oem El Cheapo plastic bushes are wearing out very quickly.
Staight replacement, no engineering required. R828


I can put more needle bearing kits together if necessary but in the past it looked as if no one really cares how wobbly those poor little bikes are :-\

I also still have a box full of DR200 spares (new).Mostly consumables such as brake pad pin lock washers and breakables. Will list and offer later.
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on February 11, 2013, 04:24:43 pm
LX - Oilcooler  - PM Sent

Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on February 11, 2013, 04:42:21 pm
 ®©errie : PM Sent

Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on February 11, 2013, 04:57:46 pm
Sláinte Mhaith : Voltage regulator, stator coil and braided brake hose.
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on February 11, 2013, 04:58:28 pm
Goose, any update on how to get the kick starter shaft out?
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on February 11, 2013, 05:00:22 pm
There is now not much of value left apart from the clutch and gear box. The clutch basket looks ok if anyone is interested. CDI available again. The front wheel , hub, rim and spokes looks OK and has a usable front tyre. Kings I think.
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: Goose on February 11, 2013, 05:31:35 pm
Goose, any update on how to get the kick starter shaft out?


 :-[ :-[  all I have been able to find is this parts diagram below. Seems item # 14 is a circlip that might be the thing holding the shaft in place..... but that might well be on the opposite side of the engine...?

Does this help at all........?

The two attached pics seem to show that the shaft/gear assembly comes out as one item...?
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on February 11, 2013, 05:42:53 pm
OK,

I have parts from 9 to 16. I think I'll have to split the engine since those splines don't look like they'll come out through the hole in the casing. I'll try tomorrow if I get a chance.
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: ®©errie on February 11, 2013, 05:45:10 pm
According to the pic the cdi wont fit my model bike :(
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: kelly007 on February 11, 2013, 09:13:15 pm
Im still interested in the front disc if it looks ok and is available...
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on February 12, 2013, 07:39:30 am
Im still interested in the front disc if it looks ok and is available...

You don't want to take the whole wheel?
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: kelly007 on February 12, 2013, 08:49:18 pm
Wouldnt mind but postage will be a pain. R200 for disc if its decent and nobody takes it with the wheel
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: Goose on February 12, 2013, 09:33:52 pm
Wouldnt mind but postage will be a pain. R200 for disc if its decent and nobody takes it with the wheel


well matey - I have some small items - where in the WC are you... maybe the Capetonians can share some transport costs....?
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on February 13, 2013, 08:45:53 am
Im still interested in the front disc if it looks ok and is available...

Here's the disc. Looks like an aftermarket one as is different to the one on my DR200. Maybe 0.5mm wear (eyeballed)
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on February 13, 2013, 08:51:59 am
Come guys, a few more bits and I might break even on this deal........
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: lecap on February 13, 2013, 10:10:10 am
I've got DR200SE leftover as follows:

2x clutch lever 57620-15D11 clutch lever n.p. R100ea.
1x 58200-44AB1 clutch cable n.p. R200
1x 58300-44AA0 throttle cable n.p. R160
2x 59346-13A00 lock washer n.p. R26 (needed for front brake pad replacement)
1 set wheel bearings Jap. generics (NSK) n.p. R200

Everything brand new. The individual prices of the Suzuki parts are 2007 US$ prices. It will probably be around twice as expensive if you buy locally and today.

Everything for sale ONLY as a lot for R 500 plus postage if required. parts fit all "late" Djebel 200 and DR200SE from 1996 onwards.
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on February 14, 2013, 12:52:51 pm
Goose, any update on how to get the kick starter shaft out?


 :-[ :-[  all I have been able to find is this parts diagram below. Seems item # 14 is a circlip that might be the thing holding the shaft in place..... but that might well be on the opposite side of the engine...?

Does this help at all........?

The two attached pics seem to show that the shaft/gear assembly comes out as one item...?


Goose, the engine definitely needs to be split to get that shaft out, but there are too many stripped bolts to split it easily, so its too much of a mission to get it out without taking a grinder and cutting a hole in the case. Do you still want the carb? Can I post you the whole engine? Any other ideas?
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: Goose on February 14, 2013, 01:14:27 pm
Goose, any update on how to get the kick starter shaft out?


 :-[ :-[  all I have been able to find is this parts diagram below. Seems item # 14 is a circlip that might be the thing holding the shaft in place..... but that might well be on the opposite side of the engine...?

Does this help at all........?

The two attached pics seem to show that the shaft/gear assembly comes out as one item...?


Goose, the engine definitely needs to be split to get that shaft out, but there are too many stripped bolts to split it easily, so its too much of a mission to get it out without taking a grinder and cutting a hole in the case. Do you still want the carb? Can I post you the whole engine? Any other ideas?


 :'( :'(

Yep - want the carb & kickstarter.......... please?

What will the weight of the engine be..........?  Cost - would probably be horrendous..........     where in the world are you - maybe I can skollie a lift for the thing - or maybe someone else could try get it out...?
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: Spozzy on February 14, 2013, 01:19:46 pm
Just found this post, rather late, I'm interested in the wheels if they are serviceable.
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on February 14, 2013, 02:43:59 pm
Goose, any update on how to get the kick starter shaft out?


 :-[ :-[  all I have been able to find is this parts diagram below. Seems item # 14 is a circlip that might be the thing holding the shaft in place..... but that might well be on the opposite side of the engine...?

Does this help at all........?

The two attached pics seem to show that the shaft/gear assembly comes out as one item...?


Goose, the engine definitely needs to be split to get that shaft out, but there are too many stripped bolts to split it easily, so its too much of a mission to get it out without taking a grinder and cutting a hole in the case. Do you still want the carb? Can I post you the whole engine? Any other ideas?


 :'( :'(

Yep - want the carb & kickstarter.......... please?

What will the weight of the engine be..........?  Cost - would probably be horrendous..........     where in the world are you - maybe I can skollie a lift for the thing - or maybe someone else could try get it out...?

Where's our friend LouisXander, isn't he quite handy with a spanner? Maybe I can give the engine to him and he can get it out?
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on February 14, 2013, 02:46:17 pm
Just found this post, rather late, I'm interested in the wheels if they are serviceable.

The front wheel, hub rim and spokes seem fine . The back wheel is fucked. I'll throw that in for free!. Make me an offer.... The front disk is going to DJ I think?
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: Goose on February 14, 2013, 03:14:47 pm
Goose, any update on how to get the kick starter shaft out?


 :-[ :-[  all I have been able to find is this parts diagram below. Seems item # 14 is a circlip that might be the thing holding the shaft in place..... but that might well be on the opposite side of the engine...?

Does this help at all........?

The two attached pics seem to show that the shaft/gear assembly comes out as one item...?


Goose, the engine definitely needs to be split to get that shaft out, but there are too many stripped bolts to split it easily, so its too much of a mission to get it out without taking a grinder and cutting a hole in the case. Do you still want the carb? Can I post you the whole engine? Any other ideas?


 :'( :'(

Yep - want the carb & kickstarter.......... please?

What will the weight of the engine be..........?  Cost - would probably be horrendous..........     where in the world are you - maybe I can skollie a lift for the thing - or maybe someone else could try get it out...?

Where's our friend LouisXander, isn't he quite handy with a spanner? Maybe I can give the engine to him and he can get it out?


:notworthy: :notworthy::notworthy::notworthy::notworthy:
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: LouisXander on February 15, 2013, 09:29:59 am
I'm here guys! Sorry, a KTM kept me busy for 2 weeks!! :imaposer: Steve, I owe you R300 ne?

Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: Goose on February 15, 2013, 09:33:01 am
I'm here guys! Sorry, a KTM kept me busy for 2 weeks!! :imaposer: Steve, I owe you R300 ne?




Oom.... kan oom asseblief help om daai moere los te maak....?  groot 'seblief?   ???
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on February 15, 2013, 09:48:19 am
I'm here guys! Sorry, a KTM kept me busy for 2 weeks!! :imaposer: Steve, I owe you R300 ne?




Oom.... kan oom asseblief help om daai moere los te maak....?  groot 'seblief?   ???

Its probably easier just to take a grinder and cut it out.
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: Spozzy on February 15, 2013, 09:51:53 am
Just found this post, rather late, I'm interested in the wheels if they are serviceable.

The front wheel, hub rim and spokes seem fine . The back wheel is fucked. I'll throw that in for free!. Make me an offer.... The front disk is going to DJ I think?

I have no idea, How does R300 sound?
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on February 15, 2013, 10:19:14 am
Sounds good to me, when do you want to come and fetch? Who is going to take the disc? You or DJ or kelly?
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on February 17, 2013, 01:43:18 pm
I'm here guys! Sorry, a KTM kept me busy for 2 weeks!! :imaposer: Steve, I owe you R300 ne?



Do you want me to post the oil cooler rather? Its less that a Kg. should only cost about R50 for postage?
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: Goose on March 18, 2013, 10:30:52 pm
Well - we finally managed to get the goodies from the Post Office............  what a nightmare this strike caused!!  :eek7:

DB mate.............  here's another request.. if at all you still have the Ignition & Key............ bastids tried to steal my son's DR200 and totally messed the ignition with a screwdriver............  :'(
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on March 19, 2013, 07:24:40 am
I'll check, but I think the key was a screwdriver on this bike....

I hope everyone has their bits now, what a pain in the ass from the PO.
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: Goose on March 19, 2013, 09:24:01 am
I'll check, but I think the key was a screwdriver on this bike....

I hope everyone has their bits now, what a pain in the ass from the PO.

 :thumleft:   
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: IanF on July 16, 2013, 06:13:42 pm
Seat and headlight?
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: chopperpilot on July 16, 2013, 06:15:56 pm
Seat and headlight?

DB9 will have to confirm, but I doubt if any spares are left. :(
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: DeepBass9 on July 16, 2013, 06:47:39 pm
Seat and headlight?

Sorry, just about nothing left. Just a carcass.
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: IanF on July 16, 2013, 07:03:46 pm
Ok thanks.
Title: Re: DR200. Rolling chassis/spares up for grabs.
Post by: chopperpilot on July 16, 2013, 07:04:40 pm
Seat and headlight?

Sorry, just about nothing left. Just a carcass.

Obtained the last few spares from DB9. :thumleft:

Bought a complete non-runner from a fellow WD. Needs a carb clean and some TLC. Would also like to do the kick starter upgrade. :thumleft: