Author Topic: Easy DRZ screen: template added (Read 2211 times)

Torque Curve · « **Reply #20 on:** September 25, 2012, 12:28:10 pm »

Quote from: flex on September 25, 2012, 12:08:05 pm

Excellent thread !!!!
Good work there
Your screen not too high maybe ?
That pic of the "dakar" DRZ screen high looks brilliant. Compliments on your excellent work bud

Yes it could be too high by an inch or two. I'll trim it down if needed, once its in use .

Casting from Turd · « **Reply #21 on:** September 25, 2012, 12:36:04 pm »

This one I want to SUB......... Great thread and I want to make one for my XR650L

The Rock · « **Reply #22 on:** September 25, 2012, 01:03:31 pm »

please tell me more about this polistone stuff. a google search didnt help much - got some strange results!

is it quite rigid like perspex/polycarb or is it more "floppy"?

you say it can be bent at room temp - without cracking?

on which side do you make the 1mm deep cut? i would imagine on the outside, but doesnt that look bad?

does it come in various colours and do you get it in translucent?

thanx!

Casting from Turd · « **Reply #23 on:** September 25, 2012, 01:16:29 pm »

Quote from: kaalkoejawel on September 25, 2012, 01:03:31 pm

please tell me more about this polistone stuff. a google search didnt help much - got some strange results!

is it quite rigid like perspex/polycarb or is it more "floppy"?

you say it can be bent at room temp - without cracking?

on which side do you make the 1mm deep cut? i would imagine on the outside, but doesnt that look bad?

does it come in various colours and do you get it in translucent?

thanx!

Looks cool hey, Mr hairless Guava?

The Rock · « **Reply #24 on:** September 25, 2012, 03:24:25 pm »

Quote from: Casting from Turd on September 25, 2012, 01:16:29 pm

Looks cool hey, Mr hairless Guava?
[/quote]
yes, Mr Turd, it looks like cool stuff!

Frannarossi · « **Reply #25 on:** September 25, 2012, 04:48:26 pm »

As jy klaar is met als kan jy mos vir ons 'n fotos post en dan nog so paar stelle ekstra maak en verkoop aan die van ons wat belangstel?

mtbbiker · « **Reply #26 on:** September 25, 2012, 05:02:06 pm »

Quote from: Torque Curve on September 24, 2012, 08:53:57 pm

Template for one half of full fairing.

Wat se ligte gaan jy gebruik, dit was my grootste kopseer toe ek die Meerkar gebou het, ek wou 'nKtm 990 se lig gebruik maar dit was bietjie duur.Ps ek is besig met weergawe 2, ek het vir my 18l IMS tank gekoop

Torque Curve · « **Reply #27 on:** September 25, 2012, 05:14:13 pm »

Quote from: kaalkoejawel on September 25, 2012, 01:03:31 pm

please tell me more about this polistone stuff. a google search didnt help much - got some strange results!

is it quite rigid like perspex/polycarb or is it more "floppy"?

you say it can be bent at room temp - without cracking?

on which side do you make the 1mm deep cut? i would imagine on the outside, but doesnt that look bad?

does it come in various colours and do you get it in translucent?

thanx!

Polistone is a trade-name for polypropylene and/or polyethylene PP and PE which is sold by:
http://www.maizey.co.za/engineering

the 1mm scour is to give a straight bend. I have had success with a small blow-torch to heat bend the PP but it's difficult over long lengths.

The stuff is cheap, R70 for 600x600mm, so get a piece and play around with it. I'm guessing this is what Hyde plastics use for most of their protective items which they heat with hot air guns for some applications.

Torque Curve · « **Reply #28 on:** September 25, 2012, 05:15:17 pm »

Quote from: Frannarossi on September 25, 2012, 04:48:26 pm

As jy klaar is met als kan jy mos vir ons 'n fotos post en dan nog so paar stelle ekstra maak en verkoop aan die van ons wat belangstel?

Ja, vir jou 1150?

Torque Curve · « **Reply #29 on:** September 25, 2012, 05:18:44 pm »

Quote from: mtbbiker on September 25, 2012, 05:02:06 pm

Quote from: Torque Curve on September 24, 2012, 08:53:57 pm
Template for one half of full fairing.
Wat se ligte gaan jy gebruik, dit was my grootste kopseer toe ek die Meerkar gebou het, ek wou 'nKtm 990 se lig gebruik maar dit was bietjie duur.Ps ek is besig met weergawe 2, ek het vir my 18l IMS tank gekoop

Geen idee vir ligte nie. Die keuse van lig sal natuurlik die projek maak of breek. Koste is so 'n relatiewe begrip. Met al die geld wat ek agter enjin parte aangooi kan ek net so wel aanhou en 'n KTM lig ook koop. Ek sal die bike vir jare moet ry om die uitgawe terug te RY so dan moet die fairing mooi wees en werk.

Hou my op hoogte van daai tank van jou. Ek was mal oor my 16L acerbis tank op die vorige DRZ en sal seker weer een koop want dan kan ek shrouds en fairing daaraan vasmaak.

Frannarossi · « **Reply #30 on:** September 25, 2012, 05:26:30 pm »

Quote from: Torque Curve on September 25, 2012, 05:15:17 pm

Quote from: Frannarossi on September 25, 2012, 04:48:26 pm
As jy klaar is met als kan jy mos vir ons 'n fotos post en dan nog so paar stelle ekstra maak en verkoop aan die van ons wat belangstel?

Ja, vir jou 1150?

Nee man vir my DRZ.Dalk moet ek kyk of ek van daai poly goed hier rond kan kry

Torque Curve · « **Reply #31 on:** September 25, 2012, 05:41:26 pm »

Quote from: Frannarossi on September 25, 2012, 05:26:30 pm

Quote from: Torque Curve on September 25, 2012, 05:15:17 pm
Quote from: Frannarossi on September 25, 2012, 04:48:26 pm
As jy klaar is met als kan jy mos vir ons 'n fotos post en dan nog so paar stelle ekstra maak en verkoop aan die van ons wat belangstel?

Ja, vir jou 1150?
Nee man vir my DRZ.Dalk moet ek kyk of ek van daai poly goed hier rond kan kry

Is daai 'n FMF end-can? Hoe werk hy oppie bike?

Frannarossi · « **Reply #32 on:** September 25, 2012, 05:48:39 pm »

Jip dis 'n FMF.Hy klink niccccccceeeeeeee maar ek het hom so gekoop met die pyp op en hy's ge dyno tune by Julian in die Kaap.Moes valves en ringe doen op 22000 kms (R7200),maar nou's hy hopelik reg vir die volgende 20 000 kms!

Torque Curve · « **Reply #33 on:** September 25, 2012, 06:26:55 pm »

Flying Machine Factory. Daar's 'n video op youtube wat wys wat in daai fabriek aangaan. Eendag...

The Rock · « **Reply #34 on:** September 26, 2012, 08:17:11 am »

aha!

http://www.maizey.co.za/engineering/engineering-sheet-rods-a-tubes/polypropylene/item/319-polystone®-pp

madmax · « **Reply #35 on:** October 03, 2012, 11:22:42 am »

nice screen ... and pipe

madmax · « **Reply #36 on:** October 03, 2012, 11:23:23 am »

actually need to find a saddle that 1 can sit on

flex · « **Reply #37 on:** October 03, 2012, 12:09:22 pm »

This saddle works well for me.

Use the current saddle base, just pop out the staples in the current cover and remove cover and foam. Put it aside for later when you sell...
This saddle cover & foam cost R250. Its nice and low for me as well for technical stuff which I do.
I will probably replace the foam in mine, not good enough & maybe a bit thin. But it works well

Torque Curve · « **Reply #38 on:** October 03, 2012, 04:34:02 pm »

Quote from: madmax on October 03, 2012, 11:23:23 am

actually need to find a saddle that 1 can sit on

I like the std seat, but I'm as skinny as the padding on the seat so we find each other nicely. I have blue gripper seat cover coming via e-bay. Might mod my seat a little like this:

Blou Blitz · « **Reply #39 on:** October 08, 2012, 02:39:34 pm »

Do you guys think this screen will fit a CRF250L as well?