Author Topic: My Sidecar Project (Read 56030 times)

woody1 · « **Reply #140 on:** June 28, 2019, 10:03:16 am »

Nee net JALOERS... Sien jy maak hom so mooi met al die regte parte.
Myne was/ is 'n Brakpan special.
Die Riversdal special sal beter wees en lyk... maar sonder BMW parte.

woody1 · « **Reply #141 on:** June 28, 2019, 10:11:22 am »

Daai Actuators is moer skaars en duur in SA. Ook nie maklik om hier te kry nie.
Dus as jy hom invoer https://www.amazon.com/Progressive-Automations-Industrial-Linear-Actuator/dp/B006P58WK4/ref=sr_1_3?qid=1561709731&refinements=p_n_feature_keywords_two_browse-bin%3A7123193011&s=industrial&sr=1-3

is hy R 4000.00 sonder belastings en vervoerkostes al klaar.

Daai jack kos my R 180.00 by pawnshop.
Wiper motor wa R 150.00 by scrapyard.

I rest my case your Honour.

Ok hy lyk nie so mooi nie maar hy werk....op 'n budget

Gerrard · « **Reply #142 on:** June 28, 2019, 10:20:21 am »

Quote from: woody1 on June 28, 2019, 10:03:16 am

Nee net JALOERS... Sien jy maak hom so mooi met al die regte parte.
Myne was/ is 'n Brakpan special.
Die Riversdal special sal beter wees en lyk... maar sonder BMW parte.

daars nou al baie sidecars deur baie mense gebou oor tyd. Wat ek nou probeer is om wat na goeie idees lyk, bymekaar te sit.

Ek sal maar sien oor die actuator. Hy kan heel laaste gedoen word as daar ietsie op die budget oor is. Intussen maak ek hom manual net om my setup reg te kry

woody1 · « **Reply #143 on:** June 28, 2019, 10:31:14 am »

Doen die arm / cam gedeelte nou al. Dan maak jy net verskillende lengtes LINKS wat jy in die plek van die actuator kan insit sodat jy verstellings kan doen.

Gerrard · « **Reply #144 on:** June 28, 2019, 10:37:02 am »

Quote from: woody1 on June 28, 2019, 10:31:14 am

Doen die arm / cam gedeelte nou al. Dan maak jy net verskillende lengtes LINKS wat jy in die plek van die actuator kan insit sodat jy verstellings kan doen.

Net so

woody1 · « **Reply #145 on:** June 28, 2019, 10:39:04 am »

Lyk my ek HELP meer as jou planne tekenaar....

Gerrard · « **Reply #146 on:** June 28, 2019, 03:10:16 pm »

Ah ! The forum... we moan and bitch and donner each other, but ask for 1150 rear wheel bolts and you get some

Any body need, let me know

Gerrard · « **Reply #147 on:** June 28, 2019, 03:14:34 pm »

Got the1150 rear shock from Bakgatjaco (the man is a star). While I'm on the RT taking a ZEN ride to Woody this weekend for a cup of coffee, I'll think about mounting it.

Also want to have a good look at his rig, just to make sure I'm on the right track (not doing it like him

)

Vis Arend · « **Reply #148 on:** June 28, 2019, 03:26:53 pm »

Quote from: Gérrard on June 28, 2019, 03:14:34 pm

Got the1150 rear shock from Bakgatjaco (the man is a star). While I'm on the RT taking a ZEN ride to Woody this weekend for a cup of coffee, I'll think about mounting it.

Also want to have a good look at his rig, just to make sure I'm on the right track (not doing it like him )

Foooook, en ek dog ek sal jou ons rig kom wys die naweek, ons gaan Kirkwood Wildfees toe maar slaap op Colcester. Gaan met die karretjie as als goed gaan.

Maar aan die ander kant, jy raak nou so goed ons rig lyk skoon old school.

Gerrard · « **Reply #149 on:** June 28, 2019, 03:54:25 pm »

Quote from: Vis Arend on June 28, 2019, 03:26:53 pm

Quote from: Gérrard on June 28, 2019, 03:14:34 pm
Got the1150 rear shock from Bakgatjaco (the man is a star). While I'm on the RT taking a ZEN ride to Woody this weekend for a cup of coffee, I'll think about mounting it.

Also want to have a good look at his rig, just to make sure I'm on the right track (not doing it like him )

Foooook, en ek dog ek sal jou ons rig kom wys die naweek, ons gaan Kirkwood Wildfees toe maar slaap op Colcester. Gaan met die karretjie as als goed gaan.
Maar aan die ander kant, jy raak nou so goed ons rig lyk skoon old school.

Dis nou jammerte, maar ek moet bietjie kop skoonmaak. Daar's nog baie op julle rig wat ek wil sien. Sal wanneer die tyd kom 'n draai maak.

Vis Arend · « **Reply #150 on:** June 28, 2019, 04:18:04 pm »

Not a probs, ek en Nan gaan nog baie rondrits, sal wel plan later maak. Mooi ry en geniet die naweek.

Gerrard · « **Reply #151 on:** July 01, 2019, 10:40:11 am »

So I popped in at Woody's this weekend for a look at his sidecar set-up He acknowledges there's a lot of improvement he can make. What I've learned from his set-up is there is a wide margin for error and it will still go ok. Some will go better,, some not.

Rode behind him a while and he klapped it. His car runs just fine. So far I' happy that I'm on the right track.

woody1 · « **Reply #152 on:** July 01, 2019, 11:11:31 am »

Dankie vir die vinnige kuier.

Het jy nog kaas oor ?

Vis Arend · « **Reply #153 on:** July 01, 2019, 01:29:49 pm »

Quote from: Gérrard on July 01, 2019, 10:40:11 am

So I popped in at Woody's this weekend for a look at his sidecar set-up He acknowledges there's a lot of improvement he can make. What I've learned from his set-up is there is a wide margin for error and it will still go ok. Some will go better,, some not.

Rode behind him a while and he klapped it. His car runs just fine. So far I' happy that I'm on the right track.

Took ours out the weekend for a ride to Kirkwood and slept at Colcester. Next day to Port Alfred and then home. Just realized how we missed the old girl. She runs a charm, very happy with her setup. A little bumpy on gravel when not loaded, other than that very happy. I was surprised at the speed I could maintain without the bike struggling.

Gerrard · « **Reply #154 on:** July 01, 2019, 06:26:37 pm »

Cut hole for shock mount

Gerrard · « **Reply #155 on:** July 01, 2019, 06:27:49 pm »

Mounting brackets

Gerrard · « **Reply #156 on:** July 01, 2019, 06:29:38 pm »

Making spacers. Cut hole in 12 plate with bi-metal hole saw.. slowly

Gerrard · « **Reply #157 on:** July 01, 2019, 06:33:24 pm »

And how it mounts

Tom van Brits · « **Reply #158 on:** July 01, 2019, 06:34:16 pm »

Quote from: Gérrard on July 01, 2019, 06:29:38 pm

Making spacers. Cut hole in 12 plate with bi-metal hole saw.. slowly

Slowly with some cutting oil - its ok with a good quality hole saw but can be frustrating

Gerrard · « **Reply #159 on:** July 01, 2019, 06:55:37 pm »

Quote from: Tom van Brits on July 01, 2019, 06:34:16 pm

Quote from: Gérrard on July 01, 2019, 06:29:38 pm
Making spacers. Cut hole in 12 plate with bi-metal hole saw.. slowly

Slowly with some cutting oil - its ok with a good quality hole saw but can be frustrating

ATF !