Search results

Good day guys, I am looking for a clutch basket on a LC 8 motor, 950 or 990 should suffice. Any help would be greatly appreciated.

Guys, We are looking at doing the "fan-add" mod on a 950, and are having trouble sourcing a fan :patch:. Does anyone by any chance have one lying around? Thanks. T

Hi Guys, We are looking at riding from Kei Mouth to Coffee bay, and back in about three days, my concern is that petrol may be somewhat of an issue on the back roads, as one of us will be on a 2smoke with small tank, going to try and do the straightest route possible, and will probably have to...

Anydogs know what the number would be on a pre-2012 model? Thanks. T-dawg

Guys, Please mind my ignorance, but I want some information, what are the notable differences between the 2009e and the 2011e, looking at purchasing a 2011 that was liable for registration in 2009 for the first time, but the bike seems to have a "newer" cluster and has only done 19600 km. I...

Guys, My TPS is giving 4 v in the neutral position and .08 v in the open position, why could this be? Thanks T

Posting on behalf of another dog: These bits are available for a 2009 XT 660 Z (Tenere) 1 x Bash plate 1 x Engine protecting Crash bar. Also , (for 2007/2008) XT 660 R Complete unused exhaust. (no picture unfortunately) Contact Danie 0828093632 to make an offer.

Posting on behalf of a mate. https://www.gumtree.co.za/a-motorcycles-scooters/eastern-pretoria/2004-bmw-f+series/1001102735940910168167909

Dogs, The rear cylinder on my LC8 wept some power, between the barrel and the case, what would opinions be on using an expensive gasket material (thickness 0.3 mm) to replace the steel OEM one? Thank you for the input. T-dawg.

Any of the dogs heading out to spectate or partake in the roof?

Guys, Posting on behalf of a friend who is looking for a framework for soft luggage, if you have available let me know. Thanks T-Dawg

I know this has been debated since the beginning of time... I have to fit a new set, but pretty sure i know what is going on the front, the question now is considering all of the facts, cost, mileage, good reviews, bad reviews, percentage on road, percentage off road, wet conditions, dry...

Dogs, I noticed the last two days that the bike doesn't want to Idle lekker at the robot when I have her in gear, neutral idles fine, and sometimes she is fine when in gear, but as soon as I pull off, specially at low revs she dies, almost threw me off around the corner near the house tonight...

At what point will a LC8 motor be damaged by overheating? Did a slow technical ride at Maraisburg today, and noticed that the heat gauge was full, stopped, only to hear the water in the motor boiling. Left it to cool, and headed to the tar to get some flow through the radiator, then all was...

Guys Ek is op soen na 'n "fork cap spanner" om die vurke op my 950 te service, as iemand so gaaf sal wees om dalk vir my enetjie te kan leen teen woensdag oggend sal ek hom ewig dankbaar wees. Dankie T-Dawg

Guys, Does anyone know where I can find some billet type fuel caps for my 950, managed to fak-ap another key in the fuel cap, and I have had enough now. Thanx T-dawg.

Ouens, Reading through the manual the other sunday (as one does) I noticed that the recommended fuel for a 950 is 98 Octane or higher, and they suggest running the scoot on the alternate ignition curve for fuel lower than 98 octane, is this becuase it retards the ignition slighly or does it...

Morning Boys, Does anybody know or have spec on what the emissions of a healthy 2004 LC8 should be? Thanks. T-Dawg

Boys, I'm looking for a fan about 140mm in diameter 12v DC, if you can assist please let me know, if you have a spare KTM 950 one lying around, please don't refrain from letting me buy it, the only one I have been able to source is in Austria at the moment. Thanks. T-dawg.

To whom it may concern, Guys, my scoot doesn't have a tendency to overheat, even with slow riding at for instance De Wildt. But yesterday whilst stuck in traffic (well as stuck as one can get on a bike) the heat gauge flickered and the temp light came on, but not the fan, so i bridged out the...